- MAGNETO1_START
- MAGNETO_SET
- L:Eng1_StarterSwitch
Ignition Switch Variables
Ignition Switch Variables
I'm building my own ignition switch, and I'm struggling with the starter. I can get the starter to engage by sending the MAGNETO1_START event. However, I can not make the starter turn off. I've tried the following variables and events:
Re: Ignition Switch Variables
I'm assuming your talking about the starter motor itself, and not that you cannot rotate the switch to "off"?
I'm using an after market "Cessna" switch panel and FSUIPC (purchased) and I noticed that on all of my A2A aircraft if the engine does not start, I cannot rotate the switch to "Off" or any other position on my switch panel. I must use the mouse to rotate the switch. But, Once the engine starts, I can put the switch into any position. Not sure if this is what you're referring to?
Wish I had an answer for you, but if it is the same issue I certainly would like to know how to overcome it!
TB2
I'm using an after market "Cessna" switch panel and FSUIPC (purchased) and I noticed that on all of my A2A aircraft if the engine does not start, I cannot rotate the switch to "Off" or any other position on my switch panel. I must use the mouse to rotate the switch. But, Once the engine starts, I can put the switch into any position. Not sure if this is what you're referring to?
Wish I had an answer for you, but if it is the same issue I certainly would like to know how to overcome it!
TB2
TB2
Ocala Flight Sim Club
United States Marine Corps
Ocala Flight Sim Club
United States Marine Corps
Re: Ignition Switch Variables
Yes, that's exactly what I'm experiencing.
Normally it's not a problem, but if the engine fails to start I have to pull out the mouse, during which time the battery is draining since it's running the starter. Next thing you know I'm pulling up the maintenance hanger to recharge the battery. Very frustrating.
Normally it's not a problem, but if the engine fails to start I have to pull out the mouse, during which time the battery is draining since it's running the starter. Next thing you know I'm pulling up the maintenance hanger to recharge the battery. Very frustrating.
Re: Ignition Switch Variables
I thought that may be it! I too would like an answer, but I think it’s “built in†to the A2A aircraft. Someone may know of a way around it.
TB2
Ocala Flight Sim Club
United States Marine Corps
Ocala Flight Sim Club
United States Marine Corps
Re: Ignition Switch Variables
I've got it working!
For some reason, it works when I write 1 or 0 to "L:Eng1_StarterSwitch", but not boolean true or false.
For some reason, it works when I write 1 or 0 to "L:Eng1_StarterSwitch", but not boolean true or false.
Re: Ignition Switch Variables
That’s great!
Sadly, I’m still using FSUIPC along with the Cessnas panel configurator and do not have time to learn how to program (as you appeared to have done)
Sadly, I’m still using FSUIPC along with the Cessnas panel configurator and do not have time to learn how to program (as you appeared to have done)
TB2
Ocala Flight Sim Club
United States Marine Corps
Ocala Flight Sim Club
United States Marine Corps
Re: Ignition Switch Variables
In FSUIPC "Buttons + Switches" tab, on right hand side, for each switch position I use
the FS control for
"Magneto Off"
"Magneto Right"
"Magneto Left"
"Magneto Both"
"Magneto Start"
On Magneto Start release I use the LVAR Macro L:Eng1_StarterSwitch=SET and set the value to 0
Works perfectly!
the FS control for
"Magneto Off"
"Magneto Right"
"Magneto Left"
"Magneto Both"
"Magneto Start"
On Magneto Start release I use the LVAR Macro L:Eng1_StarterSwitch=SET and set the value to 0
Works perfectly!
Who is online
Users browsing this forum: No registered users and 2 guests